Long descriptionAeotec Smart Switch 7 is a Z-Wave Switch plug-in module specifically used to enable Z-Wave command and control (on/off) of any plug-in tool. It can report immediate wattage consumption or kWh energy usage over a period of time. In the event of power failure, non-volatile memory retains all programmed information relating to the unit’s operating status. The Plug is also a security S2 Z-Wave device, it supports Over The Air (OTA) feature for the products firmware upgrade and SmartStart network pairing feature. From to description 0 0 disable led completely 1 0 turn on between particular times only (act as night light). 2 0 display on/off status. 2 night light on time this parameter is used to configure the night light on time. user can use color cc to change the night light color(default red). only useful when parameter 1 is set to 1. rr = reserved hh = hours mm = minutes ss = seconds default = 0x00180000 means 6pm 2 4 0 2316633 1572864 from to description 0 2316633 this parameter is used to configure the night light on time.rr = reserved hh = hours mm = minutes ss = seconds default = 0x00180000 means 6pm 4 led blink duration set the duration of blink, unit second. 0 indicates that it is not blinking 1~255 set the duration 2 1 0 255 0 from to description 0 0 indicates that it is not blinking 1 255 set the duration 3 night light off time this parameter is used to configure the night light off time. only useful when parameter 1 is set to 1. rr = reserved hh = hours mm = minutes ss = seconds default = 0x00060000 means 6am 2 4 0 2316633 393216 from to description 0 2316633 this parameter is used to configure the night light off time. only useful when parameter 1 is set to 1. rr = reserved hh = hours mm = minutes ss = seconds default = 0x00060000 means 6am 6 send alert when in use send alert when in use. a scene activation set command will be sent when energy draw is above this setting value. 0 disable 1~3000 enable, unit w 2 2 0 3000 100 from to description 1 3000 enable 0 0 disable 5 led blink speed set amount of blinks per second. i.e. if set to 5, it should blink 5 times per second. 2 1 1 24 5 from to description 1 24 set amount of blinks per second. 10 over load protection turn off switch when current of load connected bypasses the maximum allowed power regardless of always on setting. unit w. 0 disable overload protection 1~1800 when watt detected above this setting value, the switch will be turned off immediately. and an over load notification will be sent. 2 2 0 1800 1800 from to description 0 0 disable overload protection 1 1800 when watt detected above this setting value, the switch will be turned off immediately. and an over load notification will be sent. 7 plug always on prevents the plug from being turned off via its button. 0 the plug will operate as normal and can be turned on or off. 1 the button on the plug will be disabled for on and off commands, but still work for network inclusion and exclusion. 2 the plug will ignore any commands to turn it off and it will ignore any use of the button (but still work for network inclusion and exclusion) 3 1 0 2 0 from to description 0 0 the plug will operate as normal and can be turned on or off. 1 0 the button on the plug will be disabled for on and off commands, but still work for network inclusion and exclusion. 2 0 the plug will ignore any commands to turn it off and it will ignore any use of the button (but still work for network inclusion and exclusion) 8 power out action set the plug’s action in case of power out. 0 last status 1 power on 2 power off 2 1 0 2 0 from to description 0 0 last status 1 1 power on 2 2 power off 9 group3 scene id set the scene id when scene activation set command sent through group3. refer parameter 6 for more information. 2 1 1 255 255 from to description 1 255 set the scene id when scene activation set command sent through group3. 11 over voltage protection this parameter is used to set the over voltage protect value, unit v. 0 disable over voltage protection 95~255 when voltage detected above this setting value, the switch will be turned off immediately. and an over voltage notification will be sent. 2 1 0 255 135 from to description 0 0 disable over voltage protection 1 255 when voltage detected above this setting value, the switch will be turned off immediately. and an over voltage notification will be sent. 24 k wh automatic report time set the automatic report time of k wh. unit second. 2 2 0 65535 600 from to description 0 65535 set the automatic report time of k wh. unit second. 23 watt automatic report time set the automatic report time of watt. unit second. 2 2 0 65535 600 from to description 0 65535 set the automatic report time of watt 25 voltage automatic report time set the automatic report time of voltage. unit second. 2 2 0 65535 600 from to description 0 65535 set the automatic report time of voltage. unit second. 41 automatic on timer acts as auto on after as soon as the switch turns off, setting is set in seconds. 0 no auto on with timer 1~86400 seconds 2 4 0 86400 0 from to description 0 0 no auto on with timer 1 86400 seconds 255 factory reset or initialization restore the product to factory settings and remove from the network. 0x55555555 restore the product to factory settings and remove from the network. other initialize all configuration parameters to default values. 2 4 0 4294967295 0 from to description 4294967295 4294967295 restore the product to factory settings and remove from the network 0 0 initialize all configuration parameters to default values. 42 report command setting which report will be sent to lifeline group when the output state is changed. 0 send nothing 1 send basic report 2 send switch binary report 3 1 0 2 2 from to description 1 0 send basic report 2 0 send switch binary report 0 0 send nothing 31 alarm response enabled by alarm settings, and determines what the switch does in the case an alarm is triggered. 0 disable , no reaction to alarm settings 1 switch is on 2 switch is off 3~255 sets rate at which switch turns on and off in seconds. (i.e. if set to 3, then switch will turn on in 0.3 seconds, and then turn off in 0.3 seconds in a cycle until user disables the alarm manually. if set to 255, then it will cycle every 25.5 seconds) 2 1 0 255 0 from to description 0 0 disable , no reaction to alarm settings 1 1 switch is on 2 2 switch is of 3 255 sets rate at which switch turns on and off in seconds. textsID Description Value 8 
