The front is elegantly designed with a uniform diffused backlight in each square. The squares can light up in all colors which can be used to show the status of a lamp, as orientation light during nighttime, visual alarm and much more. Each square is a tactile switch that can hold up to four functions and control either a wired lamp or other Z-Wave devices, e.g. other light dimmers, roller shutters and power plugs. The pushbuttons can send ’ON’, ’OFF’ and ’DIM’ commands to associated Z-Wave devices. The light dimmer can dim all dimmable light sources from 0-250 W. MATRIX 55 fits in standard 60mm CE boxes. Examples of compatible cover frames are GIRA System 55, Exxact and Elko Plus. The insert is also compatible with GIRA pushbutton sensor 2.
Long descriptionThe front is elegantly designed with a uniform diffused backlight in each square. The squares can light up in all colors which can be used to show the status of a lamp, as orientation light during nighttime, visual alarm and much more. Each square is a tactile switch that can hold up to four functions and control either a wired lamp or other Z-Wave devices, e.g. other light dimmers, roller shutters and power plugs. The pushbuttons can send ’ON’, ’OFF’ and ’DIM’ commands to associated Z-Wave devices. The light dimmer can dim all dimmable light sources from 0-250 W. MATRIX 55 fits in standard 60mm CE boxes. Examples of compatible cover frames are GIRA System 55, Exxact and Elko Plus. The insert is also compatible with GIRA pushbutton sensor 2. From to description 0 43200 specifies the time in seconds. default is 300 = 5 minutes 42 multi level switch set values for pushbutton 4 byte 1: enable / disable. byte 2: upper switch value. byte 3: lower switch value. byte 4: not used – must be set to 0. 1 4 0 255 255 from to description 0 0 byte 4: not used – must be set to 0. 0 99 byte 2: when single pressing the pushbutton for on, a multilevel switch set with this value will be send to devices in association group 4 0 0 byte 1: disabled – a single activation of the pushbutton will not send commands to devices in association group 4. 0 99 byte 3: when single pressing the pushbutton for off, a multilevel switch set with this value will be send to devices in association group 4. (default = 0) 1 1 byte 1: enabled – a single activation will send commands to devices in association group 4. devices will receive commands with the values set in byte 2 and 3 (default). 255 255 byte 2: when single pressing the pushbutton for on, a multilevel switch set with this value will be send to devices in association group 4. (default) 43 binary switch set support for pushbutton 4 this parameter specifies how received binary switch set commands are handled. 1 1 0 2 2 from to description 0 0 binary switch set only controls the pushbutton indicator leds, on/off 1 1 binary switch set controls the internal switch status and the pushbutton indicator leds 2 2 binary switch set is handled as if the user had activated the pushbutton, including transmission of commands via the association groups 44 pushbutton 4 led indication this parameter specifies how the led indication is controlled. 1 1 0 7 7 from to description 0 0 internal led control is disabled, only external commands control the indication. 1 1 the led indication follows the switch status 2 2 the led indication follows the switch status – with inverted functionality 3 3 same as 1 4 4 same as 2 5 5 the led indication follows the status of the internal dimmer, on or off 6 6 the led indication follows the status of the internal dimmer with inverted functionality, on or off 7 7 the led indicator is on for 5 seconds when the pushbutton is activated 45 colour commands for pushbutton 4 led indication this parameter specifies how command class switch color commands are handled. 1 1 0 2 1 from to description 0 0 direct control; the led indication shows the received colour immediately, until the pushbutton is activated 1 1 colour command sets the colour for off indication 2 2 colour command sets the colour for on indication 46 on indication rgb saturation for pushbutton 4 this parameter specifies the saturation levels for the red, green and blue leds, when on status is indicated. (default is the on state indicated by a 50% blue colour). byte 1: colour saturation, red. byte 2: colour saturation, green. byte 3: colour saturation, blue. byte 4: led control. 1 4 0 255 255 from to description 0 255 byte 1: specifies the saturation for the red leds. (default is 0) 0 255 byte 2: specifies the saturation for the green leds. (default is 0) 0 255 byte 3: specifies the saturation for the blue leds. (default is 127) 0 255 byte 4: led indicator control; see the application note about this parameter. (default is 0) 47 off indication rgb saturation for pushbutton 4 this parameter specifies the saturation levels for the red, green and blue leds, when off status is indicated. (default is the off state indicated as a low white light on 5%). byte 1: colour saturation, red. byte 2: colour saturation, green. byte 3: colour saturation, blue. byte 4: led control. 1 4 0 255 255 from to description 0 255 byte 1: specifies the saturation for the red leds. (default is 47) 0 255 byte 2: specifies the saturation for the green leds. (default is 47) 0 255 byte 4: led indicator control; see the application note about this parameter. (default is 0) 0 255 byte 3: specifies the saturation for the blue leds. (default is 47) 10 enhanced led control this parameter can be used for enabling the enhanced led control. see document about matrix enhanced led control. 1 1 0 1 0 from to description 0 0 enhanced led control is disabled. 1 1 enhanced led control is enabled. 31 off indication rgb saturation for pushbutton 2 this parameter specifies the saturation levels for the red, green and blue leds, when off status is indicated. (default is the off state indicated as a low white light on 5%). byte 1: colour saturation, red. byte 2: colour saturation, green. byte 3: colour saturation, blue. byte 4: led control. 1 4 0 255 255 from to description 0 255 byte 4: led indicator control; see the application note about this parameter (default is 0) 0 255 byte 2: specifies the saturation for the green leds (default is 47) 0 255 byte 3: specifies the saturation for the blue leds (default is 47) 0 255 byte 1: specifies the saturation for the red leds (default is 47) 25 timer value for pushbutton 2 this parameter specifies the time used in previous configuration parameter. this parameter is only applicable if previous parameter has value 1 or 2. 1 2 0 43200 300 from to description 0 0 enhanced led control is disabled 0 43200 specifies the time in seconds. default is 300 = 5 minutes 1 1 enhanced led control is enabled 11 pushbutton debounce timer pushbutton input debounce time in 0.01 seconds resolution. 1 1 0 255 5 from to description 0 255 0 – 2.55 seconds. default is 5, which equals to a debounce filter on 50 milliseconds (0.05 seconds) 1 operating pushbutton(s) for dimmer this parameter specifies which pushbutton(s) that shall be used to control the built in dimmer. the parameter is a bitmask, so each of the values can be added together in order to have several pushbuttons to operate the dimmer. 1 1 0 8 1 from to description 0 0 no local operation of the dimmer. 1 1 pushbutton 1 controls the dimmer. 2 2 pushbutton 2 controls the dimmer. 4 4 pushbutton 3 controls the dimmer. 8 8 pushbutton 4 controls the dimmer. 2 duration of dimming this parameter specifies the duration of a full regulation of the light from 0% to 100%. a regulation of the light with 1% will take 1/100 of the specified duration. this is used when a pushbutton is held down for controlling the dimming, and when the dimming is fulfilled from other z wave devices. 1 1 0 255 5 from to description 0 0 immediately 1 127 duration in seconds. 128 255 duration in minutes (minus 127) from 1 – 128 minutes, where 128 is 1 minute 3 duration of on/off this parameter specifies the duration when turning the light on or off. 1 1 0 255 0 from to description 0 0 immediately 1 127 time in seconds 128 255 time in minutes (minus 127) from 1 – 128 minutes, where 128 is 1 minute 4 dimmer mode the dimmer can work in three different modes: on/off, leading edge or trailing edge. 0 1 0 2 1 from to description 0 0 no dimming, only on/off (0/100%). 1 1 trailing edge dimming 2 2 leading edge dimming 5 dimmer minimum level this parameter specifies the actual level of the dimmer output when set to 0%. 0 1 0 99 0 from to description 0 99 corresponds to 0 – 99% 6 dimmer maximum level this parameter specifies the actual level of the dimmer output when set to 99%. 1 1 0 99 99 from to description 0 99 corresponds to 0 – 99% 7 central scene notifications this parameter can be used for disabling central scene notifications. 1 1 0 1 1 from to description 0 0 notifications are disabled 1 1 notifications are enabled 8 double activation functionality this parameter specifies the reaction when double activating the pushbuttons. 1 1 0 1 1 from to description 0 0 double activation disabled 1 1 double activation sets light to 100% 9 triple activation of pushbutton 1 this parameter can be used for disabling the z wave network add/remove process when triple activating pushbutton 1. if disabled, the triple activation functionality can be used as a central scene notification. 1 1 0 1 1 from to description 0 0 triple activation of pushbutton 1, does not start the add/remove process. 1 1 triple activation of pushbutton 1, starts the add/remove process 17 timer value for pushbutton 1 this parameter specifies the time used in previous configuration parameter. this parameter is only applicable if previous parameter has value 1 or 2. 1 2 0 43200 300 from to description 0 43200 specifies the time in seconds. default is 300 = 5 minutes. 23 off indication rgb saturation for pushbutton 1 this parameter specifies the saturation levels for the red, green and blue leds, when off status is indicated. (default is the off state indicated as a low white light on 5%). byte 1: colour saturation, red. byte 2: colour saturation, green. byte 3: colour saturation, blue. byte 4: led control. 1 4 0 255 47 from to description 0 255 byte 3: specifies the saturation for the blue leds. (default is 47) 0 255 byte 4: led indicator control; see the application note about this parameter. (default is 0) 0 255 byte 1: specifies the saturation for the red leds. (default is 47) 0 255 byte 2: specifies the saturation for the green leds. (default is 47) 24 pushbutton 2 functionality this parameter specifies the functionality of pushbutton 2. 0 1 0 4 0 from to description 0 0 standard toggle function, the state is switched between on and off, dimming up and down. 1 1 automatic turn off after the time has expired (staircase lighting function), the time is specified in the next configuration parameter. 2 2 automatic turn on after the time has expired, the time is specified in the next configuration parameter. 3 3 always turn off or dim down. using this parameter, the pushbutton can only send ‘off’ or ‘dim down’ commands. use this in pair with another pushbutton with value 4 (see chapter 2.6 in the manual) 4 4 always turn on or dim up. using this parameter, the pushbutton can only send ‘on’ or ‘dim up’ commands. use this in pair with another pushbutton with value 3 (see chapter 2.6 in the manual) textsID Description Value 8 
