The curtain motor controller is a universal, Z-Wave Plus compatible, electric motor controller. The device allows for controlling motors of roller blinds and venetian blinds, which are single phase AC powered. The curtain motor controller allows for precise positioning of a roller blind or venetian blind slats. Precise positioning is available for the motors equipped with mechanic and electronic end switches. The device also allows for controlling on/off of lights. The module may be controlled wirelessly, through the Z-Wave network primary controller, or through the switch keys connected to it. In addition, the curtain motor controller is equipped with Power Metering and over current protection.
Long descriptionThe curtain motor controller is a universal, Z-Wave Plus compatible, electric motor controller. The device allows for controlling motors of roller blinds and venetian blinds, which are single phase AC powered. The curtain motor controller allows for precise positioning of a roller blind or venetian blind slats. Precise positioning is available for the motors equipped with mechanic and electronic end switches. The device also allows for controlling on/off of lights. The module may be controlled wirelessly, through the Z-Wave network primary controller, or through the switch keys connected to it. In addition, the curtain motor controller is equipped with Power Metering and over current protection. Short descriptionThe curtain motor controller is a universal, Z-Wave Plus compatible, electric motor controller. The device allows for controlling motors of roller blinds and venetian blinds, which are single phase AC powered. Value scene & central scene firmware updatable value updatable by consumer by rf supported meter type value electric energy supported notification types value power management system window covering control features value position aware automatic calibration supports curtains supports horizontal blinds/louvers supports up/down motion supports open/close motion association groupsGroup Number Maximum Nodes Supported End Point ID Description 2 From to description 0 0 light mode 1 1 shutter mode without positioning 2 2 shutter mode with positioning 3 3 venetian mode (up/down and slats rotation) 4 enable/disable to save positioning enable/disable to save positioning percentage, record and save current positioning every time when the curtain moves to specified position, if the working mode is configured as light mode, record on/off state. 0 1 0 0 1 from to description 0 0 disable 1 1 enable 5 enable/disable over current protection enable/disable over current protection 0: disable 1: enable, when over current detected, there are two methods to cancel alarm: 1. short press either switch button s1 or s2, the alarm will last at least 1 minute and then be cancelled. 2. re power on the curtain motor controller 0 1 0 0 1 from to description 0 0 disable 1 1 enable, when over current detected, there are two methods to cancel alarm: 1. short press either switch button s1 or s2, the alarm will last at least 1 minute and then be cancelled. 2. re power on the curtain motor controller 6 starting positioning calibration only value 1 can be written in, which means starting positioning calibration. when read, 0x01: positioning calibration completed 0x00: positioning not calibrated this parameter is only valid when parameter 3 configured as shutter mode with positioning or venetian mode (up/down and slats rotation). 0 1 0 0 0 from to description 0 0 positioning not calibrated 1 1 positioning calibration completed 7 when parameter 3 value configured as 0 (light mode), configuration of button s1 and s2 control. when parameter 3 value configured as 0 (light mode), configuration of button s1 and s2 control. 0 1 0 0 0 from to description 0 0 short press s1 to switch on/off q1. press and hold down s1 to switch on q1, then release to switch off q2. short press s2 to switch on/off q2. press and hold down s2 to switch on q2, then release to switch off q2. 1 1 short press s1 to switch on/off q1. when s1 is pressed and held down, then released, not processed. short press s2 to switch on/off q2. when s2 pressed and held down, then released, not processed. 2 2 press and hold down s1 to switch on q1, then release to switch off q2. when s1 short pressed, not processed. press and hold down s2 to switch on q2, then release to switch off q2. when s2 short pressed, not processed. 3 3 short press s1 or s2 to switch on/off of both q1 and q2 simultaneously. when s1 or s2 pressed and held down, not processed 4 4 press and hold down s1 to switch on q1 and q2. when s1 short pressed, not processed. press and hold down s2 to switch off q1 and q2. when s2 short pressed, not processed. 8 enable/disable to add the device to or remove it from a z wave network through button s1. enable/disable to add the device to or remove it from a z wave network through button s1. please refer to the parts of inclusion and exclusion for details. 0 1 0 0 1 from to description 0 0 enable 1 1 disable 9 enable/disable to send scene activation command central scene notification v3 when the switches s1 and s2 are pressed. enable/disable to send scene activation command central scene notification v3 when the switches s1 and s2 are pressed. 0 1 0 0 1 from to description 0 0 disable to send for action of both s1 and s2 1 1 enable to send for action of both s1 and s2 2 2 enable to send for action of only s1 3 3 enable to send for action of only s2 10 power change absolute threshold report, unit is w power change absolute threshold report, unit is w 0 1 0 0 10 from to description 0 0 disable absolute threshold report function 1 100 value of the power change absolute threshold, if power change value is over the threshold value, report the power change value using meter report 11 current change absolute threshold, unit is 0.1 a wiring type note: this parameter is read only 0 1 0 0 0 from to description 0 0 disable absolute threshold function 1 10 value of the current change absolute threshold, if current change value is over the threshold value, report the current change value using meter report 2 saving load state before power failure enable/disable the curtain motor controller to report state change percentage threshold (report only when change value at the specified percentage), if enabled, report when the value reaches both 0% and 99%. when the working mode is configured as light mode, as long as the state changes, the state change percentage threshold will be reported. switch multilevel report 0 1 0 0 1 from to description 0 0 disable to report actively 1 1 value to report, unit is one percent textsID Description Value 5 
